注意：請?jiān)谂渲们瓣P(guān)閉NetworkManager服務
[root@h63 ~]# service NetworkManager status && service NetworkManager start
網卡綁定一次可以綁定多個網卡，你可以使用ifconfig -a查看你的網卡信息，例如：
[root@h63 ~]# ifconfig -a

em1       Link encap:Ethernet  HWaddr 78:2B:CB:30:08:03
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:48236002 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16156472 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:4838973371 (4.5 GiB)  TX bytes:1301118550 (1.2 GiB)
          Interrupt:36 Memory:d6000000-d6012800

em2       Link encap:Ethernet  HWaddr 78:2B:CB:30:08:05
          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
          RX packets:42385720 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7283526 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:4307780986 (4.0 GiB)  TX bytes:466840625 (445.2 MiB)
          Interrupt:48 Memory:d8000000-d8012800

em3       Link encap:Ethernet  HWaddr 78:2B:CB:30:08:07
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:32 Memory:da000000-da012800

em4       Link encap:Ethernet  HWaddr 78:2B:CB:30:08:09 
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:42 Memory:dc000000-dc012800

這里有4個網卡，分別是em1、em2、em3和em4，我們把em1和em2做一個綁定，綁定模式為6（關于網卡綁定模式的介紹請看Linux網卡綁定探析），首先我給給網卡綁定后的設備起個名字bond0（名稱可以自定義），并創建：
[root@h63 ~]# vim /etc/sysconfig/network-scripts/ifcfg-bond0
DEVICE=bond0　　　　　　　　#設備名稱
BOOTPROTO=static　　　　　　#靜態IP
ONBOOT=yes　　　　　　　  　#自動啟動
IPADDR=172.16.16.63　　　　#設備綁定的IP
GATEWAY=172.16.23.254       #設備綁定的網關
NETMASK=255.255.248.0 　　 #設備綁定的掩碼
TYPE=Ethernet　　　　　　　　 #設備綁定的類型

編輯需要綁定的網卡：
[root@h63 ~]# vim /etc/sysconfig/network-scripts/ifcfg-em1

DEVICE=em1
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0　　#綁定后的設備名稱
SLAVE=yes
TYPE=Ethernet

[root@h63 ~]# vim /etc/sysconfig/network-scripts/ifcfg-em2

DEVICE=em2
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0　　#綁定后的設備名稱
SLAVE=yes
TYPE=Ethernet
說明：配置網卡時不要填寫IP地址和MAC地址

配置加載模式設置：
[root@h63 ~]# vim /etc/modprobe.conf

alias bond0 bonding
options bond0 miimon=100 mode=6

說明：mode是網卡綁定的模式，此處是模式6

也可以在/etc/modprobe.d/下創建一個文件：
[root@h63 ~]# vim /etc/modprobe.d/bond

alias bond0 bonding
options bond0 miimon=100 mode=6

綁定配置完成，重啟網絡服務
[root@h63 ~]#service network restart

查看網卡綁定的情況：

[root@h63 ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: em1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: em1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 78:2b:cb:30:08:03
Slave queue ID: 0

Slave Interface: em2
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 78:2b:cb:30:08:05
Slave queue ID: 0

至此，網卡綁定就完成了。有不對的地方，還請指教。