QT利用QPdfWriter實現繪制PDF(支持表單輸出)

更新時間：2023年01月13日 16:33:07 作者：諾謙

這篇文章主要為大家詳細介紹了QT如何利用QPdfWriter實現繪制PDF，并可以支持表單輸出。文中的示例代碼講解詳細，感興趣的小伙伴可以了解一下

之前打印PDF都是通過html形式來實現的,但是這次要做的東西,需要打印界面控件,所以需要使用QPdfWriter.

通過QPdfWriter來獲取QPainter對象,就能實現在PDF上來畫畫啦.

代碼生成的PDF如下所示:

代碼效果如下所示:

代碼如下所示：

//通過dialog來保存PDF路徑
QString mainWindow::pdfSaveAs(QString fileName)
{
        QString file="";
 
        file = QFileDialog::getSaveFileName (
        this,                               //父組件
        "另存為",                              //標題
        QString("%1/%2").arg(QStandardPaths::writableLocation(QStandardPaths::DesktopLocation)).arg(""+fileName+".pdf"),
                                                            //設置路徑, .表示當前路徑,./表示更目錄
        "PDF文件",     //過濾器,保存的類型
        Q_NULLPTR,
        QFileDialog::ShowDirsOnly);
 
        return file;
}
 
//y:表單的Y坐標
//horzBorder:水平外邊距,寫0表示沒有邊距
//row,column:行數和列數
//unitHeight:單元高度
//font:字體大小
//list:要寫入的單元數據
void mainWindow::pdfDrawForm(QPainter* paint,int y,int horzBorder,int row,int column,int unitHeight,QFont &font,QStringList& list)
{
    paint->setFont(font);
 
    paint->setPen(QPen(QBrush(QColor(0,0,0)),2));
 
    int Width = paint->viewport().width()-horzBorder*2;
 
    int unitWidth = Width/column;
 
    for(int i=0;i<row;i++)
    {
        int x= horzBorder;
 
        for(int j=0;j<column;j++)
        {
            paint->drawText(QRect(x,y, unitWidth, unitHeight), Qt::AlignCenter,list[i*column+j]);
 
            paint->drawRect(QRect(x,y, unitWidth, unitHeight));
 
            x+=unitWidth;
        }
 
        y += unitHeight;
    }
 
 
 
}
 
 
void mainWindow::pdfCreate(checkInfo &info)
{
 
//        //設置pdf保存的路徑
//        QString file_path = pdfSaveAs(QString("表單%1").arg(QDateTime::currentDateTime().toString("MMdd-hh-mm")));
//        if(file_path.isEmpty())
//            return;
 
        QString file_path =QApplication::applicationDirPath()+"/test.pdf";  
        QFile pdfFile(file_path);
        pdfFile.open(QIODevice::WriteOnly);
        QPdfWriter* pWriter = new QPdfWriter(&pdfFile);
 
        //Init Page
        pWriter->setPageSize(QPagedPaintDevice::A4);
        pWriter->setResolution(300);    //設置dpi 每個平方英寸像素為300
        pWriter->setPageMargins(QMarginsF(30, 30, 30, 30));
 
 
        QPainter* pPainter = new QPainter(pWriter);
 
        //Init Font
        QFont font[5]={QFont("宋體",26,60),QFont("宋體",26,61),QFont("宋體",26,QFont::Normal),QFont("宋體",26,QFont::Normal),QFont("宋體",26,QFont::Normal)};
        font[0].setPixelSize(86);
        font[1].setPixelSize(61);
        font[2].setPixelSize(61);
        font[3].setPixelSize(42);
        font[4].setPixelSize(54);
 
        //Painter PDF
        qDebug()<<pPainter->viewport();
        int nPDFWidth = pPainter->viewport().width();
        int nPDFHeight = pPainter->viewport().height();
 
 
        //在10%的頭部居中顯示
        int y=10;
        pPainter->setFont(font[0]);
        pPainter->drawText(QRect(0,y, nPDFWidth, 100), Qt::AlignCenter,
        m_arg.printTitle);
        y+=140;
        pPainter->setPen(QPen(QBrush(QColor(0,0,0)),5));
        pPainter->drawLine(0,y,nPDFWidth,y);
        pPainter->drawLine(0,y+18,nPDFWidth,y+18);
 
        y+=60;
 
        pPainter->setFont(font[2]);
        pPainter->drawText(QRect(100,y, nPDFWidth/2, 70), Qt::AlignVCenter | Qt::AlignLeft,
        QString("器件型號: %1").arg(info.dev.name));
 
        pPainter->setFont(font[2]);
        pPainter->drawText(QRect(nPDFWidth/2+100,y, nPDFWidth/2-100, 70), Qt::AlignVCenter | Qt::AlignLeft,
        QString("器件編號: %1").arg(info.devNum));
 
        y+=90;
 
        pPainter->setFont(font[2]);
        pPainter->drawText(QRect(100,y, nPDFWidth/2, 70), Qt::AlignVCenter | Qt::AlignLeft,
        QString("裝車車號: %1").arg(info.devCar));
 
        pPainter->setFont(font[2]);
        pPainter->drawText(QRect(nPDFWidth/2+100,y, nPDFWidth/2-100, 70), Qt::AlignVCenter | Qt::AlignLeft,
        QString("試驗日期: %1").arg(info.checkDate));
 
        y+=110;
 
 
        pPainter->setFont(font[1]);
        pPainter->drawText(QRect(0,y, nPDFWidth, 80), Qt::AlignVCenter | Qt::AlignLeft,
        "減 振 器 標 準 參 數");
 
        y+=120;
 
 
        QStringList list;
        list<<"速度"<<"壓力"<<"拉力"<<"阻尼系數"<<"不對稱率"<<"正允差"<<"負允差";
        list<<info.dev.speed+"m/s"<<info.dev.yaLi+"kN"<<info.dev.laLi+"kN"<<\
              info.dev.zhuNi+"kNs/m"<<info.dev.buDuiC+"%"<<info.dev.zYunCha+"%"<<info.dev.fYunCha+"%";
        pdfDrawForm(pPainter,y,0,2,7,100,font[3],list);
 
        y+=260;
 
 
        pPainter->setFont(font[1]);
        pPainter->drawText(QRect(0,y, nPDFWidth, 80), Qt::AlignVCenter | Qt::AlignLeft,
        "示 功 圖");
        y+=100;
 
        //獲取界面圖片
        int imageBorder=150;        //設置圖片水平邊距為150
 
        QPixmap pixmap = QPixmap::grabWidget(m_checkChart, m_checkChart->rect());
 
        float x = (float)(nPDFWidth-imageBorder*2)/(float)pixmap.width();
 
        pixmap= pixmap.scaled(nPDFWidth-imageBorder*2, x*pixmap.height(),Qt::IgnoreAspectRatio);    //根據大小比例,來放大縮小圖片
 
        pPainter->drawPixmap(imageBorder, y, pixmap);
 
        y+=pixmap.height()+90;
 
        pPainter->setFont(font[1]);
        pPainter->drawText(QRect(0,y, nPDFWidth, 80), Qt::AlignVCenter | Qt::AlignLeft,
        "減 振 器 測 試 結 果");
 
        y+=120;
 
        list.clear();
        list<<"拉伸行程:"<<QString::asprintf("%.2fmm",info.laSheng)<<"壓縮行程:"<<QString::asprintf("%.2fmm",info.yaSuo)<<"最大速度:"<<QString::asprintf("%.3fm/s",info.speed)<<"阻尼系數:"<<QString::asprintf("%.2fkNs/m",info.speed)
             <<"最大壓力:"<<QString::asprintf("%.2fkN",info.max)<<"壓力偏差:"<<QString::asprintf("%.2f%",info.maxBaiFengb)<<"最大拉力:"<<QString::asprintf("%.2fkN",info.min)<<"拉力偏差:"<<QString::asprintf("%.2f%",info.minBaiFengb)
              <<"不對稱率:"<<QString::asprintf("%.2f%",info.buduic)<<"運行時間:"<<QString::asprintf("%dS",info.runDate)<<"試驗結果:"<<info.result<<"曲線結論:"<<info.ChartResult;
        pdfDrawForm(pPainter,y,0,3,8,100,font[3],list);
 
        y+=400;
 
        pPainter->setFont(font[4]);
        pPainter->drawText(QRect(50,y, nPDFWidth/3, 80), Qt::AlignVCenter | Qt::AlignLeft,
        QString( "試驗員: %1").arg(m_userLoginInfo->name));
 
        pPainter->drawText(QRect(nPDFWidth/3+50,y, nPDFWidth/3, 80), Qt::AlignVCenter | Qt::AlignLeft,
        QString( "檢查員簽字: "));
 
        pPainter->drawText(QRect(nPDFWidth/3*2,y, nPDFWidth/3, 80), Qt::AlignVCenter | Qt::AlignLeft,
        QString( "簽字日期: "));
 
       // pWriter->newPage(); //寫下一頁
 
        //繪制完畢
        delete pPainter;
        delete pWriter;
        pdfFile.close();
 
 
        //通過其它PDF閱讀器來打開PDF
        QDesktopServices::openUrl(QUrl::fromLocalFile(file_path));
}

到此這篇關于QT利用QPdfWriter實現繪制PDF(支持表單輸出)的文章就介紹到這了,更多相關QT QPdfWriter繪制PDF內容請搜索腳本之家以前的文章或繼續瀏覽下面的相關文章希望大家以后多多支持腳本之家！

您可能感興趣的文章: